BRANDT KTD

Small and compact edgebanders with direct glue application by a glue roller; For machines of the same size, but for processing of edge material, pre-coated with hot-melt glue, see the series Brandt T and Brandt KTV

Types

KTD 1

  • Small edgebanding machine for curved and straight workpieces; Curved workpieces are guided past the driven pressure roller, placed on a stencil. The pressure roller supports the workpiece feed. However, the workpieces are mostly guided by hand.
  • Work procedures: supply of the edge material, gluing on of the material, cutting of the roll material (by a pneumatic trimmer)
  • Technical data:
  • Workpiece thickness 10 up to 40 mm
  • Thickness of the edge material 0.4 up to 1 mm
  • Feed rate with manual support: 4 m/min
  • Successor model is the KTD 51

KTD 13 and 14

  • Small edgebanding machine for straight workpieces with its own, top-acting workpiece feed
  • Work procedures: supply of the edge material, gluing on of the material, cutting of the roll material, flush cutting (KTD13) / flush milling (KTD14)

KTD 51

  • Construction with small differences to the KTD 1, but changed design up to a control panel located on the top
  • Technical data:
  • Workpiece thickness 10 up to 40 mm
  • Thickness of the edge material 0.5 up to 1 mm
  • Feed rate with manual support 4 m/min (1980s models), 4 up to 9 m/min for machines with control panel on the top (1990s models)
  • Options:
  • Automatic magazine for single strips
  • Digital preset for the length of the edge material

KTD 52 and 53

  • Small edgebanding machine with its own workpiece feed from the bottom, with the principle of inclined rollers, for the edgebanding on straight workpieces
  • In the early 1980s, built as bench machine, in the late 1980s, with its own machine frame
  • Work procedures: supply of the edge material, cutting of the roll material, gluing on of the material, precise cross cut (only KTD53), flush milling
  • Technical data:
  • Workpiece thickness 10 up to 40 mm
  • Thickness of the edge material 0.4 up to 1.5 mm, cutting of the roll material up to 0.8 mm
  • Feed rate 7 m/min

KTD 63, 64 and 65

  • Compact edgebanding machines for edgebanding on straight workpieces with the feed system of 'large' edgebanders, consisting of feeding chain and upper pressure
  • Work procedures:
  • Supply of the edge material (automatic coil magazine, optional automatic magazine for single strips)
  • Cutting of the roll material
  • Cross cut with two motors (only KTD 64 and 65)
  • Flush milling with horizontal and vertical tracing
  • Chamfer milling (with this term Brandt refers to the edge finish with a buffing unit, only KTD 65)
  • Technical data:
  • Workpiece thickness 10 up to 40 mm
  • Thickness of the edge material from the roll 0.8 mm
  • Edgeband thickness of fixed lengths strips 1.5 mm for the KTD 63, up to 3 mm for the KTD 64 and 65
  • Feed rate 11 m/min (early 1980s) and 9 m/min (late 1980s)

KTD 72

  • Small edgebanding machine for straight edges and shaped parts, with driven pressure roller, which supports the workpiece feed
  • Further development of the KTD 51
  • Work procedures:
  • Supply of the edge material, optional with automatic magazine for single strips
  • Cutting of the roll material
  • Flush milling for straight workpieces optional
  • Technical data:
  • Workpiece thickness 10 up to 55 mm
  • Thickness of the edge material up to 3 mm
  • Feed rate with manual support 4 up to 9 m/min

KTD 82

  • Small edgebanding machine for shaped parts
  • Mobile gluing aggregate for processing of large, shaped parts, quick conversion to a stationary machine for processing of small parts
  • Cutting of the roll material to a preset length
  • Technical data:
  • Workpiece thickness 16 up to 40 mm
  • Thickness of the edge material 0.4 up to 3 mm

KTD 720

  • Successor model of the KTD 72, similar in construction, but without the option of flush milling of straight workpieces

KTD 820

  • Successor model of the KTD 82, similar in construction
BRANDT KTD
Production:
approx. 1983
2017
WOOD TEC VALUE

Valuate your used BRANDT KTD now for free and calculate the current market price. Quick, simple and independent!

Machine valuation

Images

Formteil-Kantenanleimmaschine KTD1
BRANDT, 1983
KTD14
BRANDT, 1993
KTD51
BRANDT, 1993
KTD53
BRANDT, 1987
KTD65
BRANDT, 1989
KTD 72
BRANDT, 2000
KTD 820
BRANDT, 2013

Product brochures and leaflets (3)

more
less

Type